Mini Micro Profilers
A novel portable instrument has been designed for in-situ
microsensor measurements. The micro profiler, which can be equipped
with microsensors for measurements of oxygen, pH, sulphide (S
-- or H2S) and temperature, is ideal for a
wide range of applications including:
- Oxygen respiration.
- Benthic primary production.
- Quantification of sulphide oxidation and sulphate reduction by measurement with a sulphide (gas or ion) microsensor for use inbio-filmsand sediments.
Profiling measurements can be carried out with a spatial
resolution of 50 µm in numerous locations including:
- At the sediment-water interface (from tidal flats to 100 m water depth).
- In bio-films, for studying the transformation of organic matter.
- Under ice, for studying respiration and primary production of ice-algae.
Weight, in air: 10 kg
Weight, in water: 8 kg
Total height: 1,0 m
Distance between feet: 0,75 m
The mini microprofilers are developed in cooperation
with -
Dr. Søren Rysgaard, Senior Scientist, National Enviromental
Research Institute, Denmark
Jens K. Gundersen, Institute of Biological Scienses, University of
Aarhus Denmark.
Pressure compensated sensor house (100.154) made of acrylic (PMMA) with a screw-in tightening ring in the top made of (POM) and 3 pcs. O-rings. The bottom is protected by an AISI 316 stainless steel ring. Tested for 800 atmospheres pressure.
Pressure compensated sensor house
Click on photo for illustration and working principles.
Pressure stable connectors
Gold plated, 3 or 4-pin connectors made of AISI 316 stainless
steel with 3/8" UNF thread and 3 pcs. of wire, length 25 cm.
Tested for a pressure of 800 atmospheres.
- 100.192 - 3 pin
- 100.193 - 4 pin
- Pressure stable "Dummy" 100.194 -
- Connector made of AISI 316 stainless steel with 3/8" UNF thread. Tested for 800 atmospheres pressure.
Camera housing
Housing: AISI 316 stainless steel. Internal diameter: 72 mm
Length: 120 mm.
Front glass: 10 mm Acrylic (PMMA)
Max. depth: 200 m
Connector for transmission: 1 pc Subconn
Finish: Electro polish
Ordering no.: 100.196
Lamp for 12 V
12 volt DC 35 watt lamp 38°
Housing: AISI 316 stainless steel
Finish: Electro polish
Ordering no.: 100.195
Camera housing
Housing: AISI 316 stainless steel
Internal diameter: 50 mm
Length: 120 mm
Front glass: 10 mm Acrylic (PMMA)
Max. depth: 200 m
Connector for transmission: 1 pc Subconn
Finish: Electro polish
Ordering no.: 100.199
Datalogger box
Housing: AISI 316 stainless steel
Internal diameter: 125 mm
Length: 340 mm
Front glass: 10 mm Acrylic (PMMA)
Max. depth: 200 m
Connector for transmission: 2 pc Subconn connectors (10 pins) (1 x
BH10F-SS and 1 x BH10M-SS).
Finish: Electro polish
Ordering no. 100.198
| Description | Ordering No. |
| Model 1:
One Mini microprofiling system with a detachable 3-leg base, made in 4 mm acid-proof AISI 316 stainless steel. The system is furnished with 1 MCBH5M Subconn connection and 2 end-stop magnets (Neodymium) and is pressure compensated to 6000 m depth. Sensor electronics housing, housing cable, and motor control system are not included in the price. |
100.175 |
| Model 2:
One Mini microprofiling system with a detachable 3-leg base adjustable in height, made in 4 mm acid-proof AISI 316 stainless steel. The system is furnished with 1 MCBH5M Subconn connection and 2 end-stop magnets (Neodymium) and is pressure compensated to 6000 m depth. Sensor electronics housing, housing cable, and motor control system are not included. |
100.176 |
|
Accessories: |
|
| One Computer (Artica Controller) |
|
| Computer box.
One yellow rugged polycarbonate plastic box (flighcase). Dimensions: Length = 356 mm Width = 264 mm Height = 154 mm for Artica controller with 4 micro Subconn connectors and engraved cable signs: 1 MCBH8F connector (for motor system), 1 MCBH6M (for sensor electronics housing). 1 MCBH4F connector (for PC). 1 MCBH2M connector (for battery). |
100.207 |
| Motor cable 25 meter.
One 25 meter 8 conductor 0,50 mm² (Polyurethane) cable from motor system to Artica-box with 2 end-stop sensors (Reed switches) and 2 cast micro-Subconn connectors (MCIL5F and MCIL8M). Cable strength 200 kg. |
100.203 |
| Motor cable 50
meter.
One 50 meter 8 conductor 0,50 mm² (Polyurethane) cable from motor system to Artica-box with 2 end-stop sensors (Reed switches) and 2 cast micro-Subconn connectors (MCIL5F and MCIL8M). Cable strength 200 kg. |
100.204 |
|
Communication cable 3 meter. 1 PC. 3 meter 4 conductor 0,75 mm² (rubber cable HO-7) from Artica-box to computer with 1 pc. cast micro-subconn connector. (MCIL4-M). |
100.190 |
| Battery cable 3
meter.
1 pc 3 meter 2 conductor 0,75 mm² (rubber cable HO-7) from Battery box to Artica-box with 1 pc cast micro-subconn connector. (MCIL2-F). |
100.191 |
| Releaser to Niskin water sampler.
Assembly of releaser system to Niskin water sampler on mini-micro profiler. |
100.210 |
| Battery charger.
1 pc. 24 Volt DC 2,5 amp electronic battery charger (laboratory-current supply) with 2 pcs digital instrument. 0 to 30 Volt DC 0 - 2,5 Amp with adjustable current limit, plus a CCE connector. |
100.211 |
| Sensor cable 25 meter.
One 25 m 6 conductor cable 0,75 mm² polyurethane shielded cable from sensor electronics housing to Arctica box with 2 cast micro-Subconn connectors. (MCIL6M and MCIL6F ) Cable strength 200 kg |
100.205 |
| Sensor cable 50
meter.
One 50 meter 6 conductor 0,75 mm² polyurethane shielded cable from sensor electronics housing to Arctica box with 2 cast micro-Subconn connectors (MCIL6M and MCIL6F ) Cable strength 200 kg |
100.206 |
| Sensor electronics house.
One sensor electronics housing (cylinder) for 4 sensors made in brass and surface-treated with seawater-proof 2-component paint. The housing is delivered with four 3/8" UNF threaded holes for 3- and 4-pin connectors and one MCBH6M micro-Subconn connector. Including PVC holder for four amplifier electronics, but excluding sensors, connectors, and amplifiers. |
100.183 |
|
Holder for sensor house. 2 adjustable fittings for sensor electronics housing made in AISI 316 stainless steel with POM protection lining. |
100.184 |
| 3-Pin connector.
One 3-pin connector with 3/8" UNF thread made in AISI 316 stainless steel and with 3 gold-plated pins and 25 cm wires. Pressure tested to 800 bar. |
100.192 |
|
4-Pin connector. One 4-pin connector with 3/8" UNF
thread made in |
100.193 |
| Dummy for connector.
One 'Dummy' connector with 3/8" UNF thread made in |
100.194 |
| Acrylic sensor house.
One pressure compensated acrylic sensor house
excluding sensor |
100.154 |
| Niskin Water sampler.
One 250 ml water sampler model 'Niskin' mounted on measuring system. |
100.179 |
| Transport box.
Transport box made in birchwood, dimensions: length = 640 mm, height = 350 mm, width = 440 mm, weight 10 kg. |
100.180 |
| Battery box 10 Amp/h.
One 24 Volt DC 10 Amp/h battery box made in AISI 316 stainless steel. Maximum deployment depth: 150 m. |
100.201 |
| Battery box 20 Amp/h.
One 12 Volt DC 20 Amp/h battery box made in AISI 316 stainless steel. Maximum deployment depth: 150 m. |
100.202 |
| Battery box 15 Amp/h.
One 24 Volt DC 15 Amp/h battery box made in AISI 316 stainless steel. Maximum deployment depth: 150 m. |
100.208 |
| Battery box 30 Amp/h.
One 12 Volt DC 30 Amp/h battery box made in AISI 316 stainless steel. Maximum deployment depth: 150 m. |
100.209 |
| 12 V Lamp.
One 12 Volt DC 35 Watt lamp, 38º dispersion. The lamp is built into an AISI 316 stainless steel housing with one MCBH2M micro-Subconn connector mounted in the lid. Inner diameter ø50mm x length 100 mm. Maximum deployment depth: 150 m. |
100.195 |
| Small video camera house.
One housing for video camera without Subconn connectors made in AISI 316 stainless steel. Dimensions: Inner diameter Ø50 mm. Length 120 mm. Fits small cameras. Two rotatable fittings included. Maximum deployment depth: 150 m. |
100.199 |
| Small video camera house.
One housing for video camera without Subconn connectors made in AISI 316 stainless steel. Dimensions: Inner diameter Ø72 mm. Length 120 mm. Fits small cameras. Two rotatable fittings included. Maximum deployment depth: 150 m. |
100.196 |
VERY IMPORTANT All quoted prices are subject to alterations if any changes in construction, material or delivery time is requested by the purchaser after final quoting/ordering or during the manufacturing process. |
|
Do not use alcohol for cleaning acrylic
parts
| Reference list for Mini Micro
Profiler: |
|
| Dr. Jens
Gundersen, UNISENSE, Science Park, Aarhus, Denmark jkg@unisense.com |
Dr. Lars Riis
Damgaard, UNISENSE, Science Park, Aarhus, Denmark lrd@unisense.com |
| Dr. Søren Ryesgaard, National Environmental Research Institute, Silkeborg, Denmark SR@dmu.dk |
NASA, Ames Research Center, California, USA |
| Dr. Ole
Pedersen, Freshwater Biological Laboratory, University of Copenhagen Hillerød, Denmark opedersen@zi.ku.dk |
Dr. Lesley
Warren, School of Geography and Geology McMaster University, Hamilton, ON L8S 4K1 CANADA warrenl@mcmaster.ca |
| Reference list for
Microprofiler for the sediment-water interface |
|
| Dr. Jens K.
Gundersen, UNISENSE, Science Park Aarhus, Denmark jkg@unisense.com |
Dr. Gary
Fones, Environmental Science Dept. I.E.N.S. Lancaster University, Lancaster, Lancashire, UK g.fones@lancaster.ac.uk |
| Dr. Ronni Glud Marine Biological Laboratory, University of Copenhagen, Helsingør, Denmark mblrg@centrum.dk |
Dr. Christophe
Rabouille, Laboratoire des Sciences du Climat et de 1'Environnement, Unité Mixte de Recherche CNRS-CEA Domaine de CNRS - Bat 12 - Avenue de la Terrasse, F-91198, Gif-sur-Yvette, France Christophe.Rabouille@lsce.cnrs-gif.fr |
| Prof. Bo
Barker Jørgensen, Max-Planck Institute, Bremen, Germany bjoergen@mpi-bremen.de |
Dr. Anders
Tengberg Analytical and Marin Kemi Göteborg University, Sverige anders@amc.chalmers.se |
| Dr. Kevin Steven
Black, Gatty Marine Laboratory, St. Andrews, Scotland ksb2@st-andrews.ac.uk |
Dr. Sibylle
Grandel, GEOMAR, Dep. of Marine Environmental Geology, Kiel, Germany sgrandel@geomar.de |
| Dr. Graham
Shimmield, Scottish Association for Marine Sciences Dunstaffnage Marine Laboratory, Oban, Argyll, Scotland www.ccms.ac.uk |
Prof. Dr.
Michael Schlüter Alfred-Wegener-Institut Bremerhaven Am Handelshafen mschlueter@awi-bremerhaven.de |
| Dr.Eric Breuer Centre for Coastal and Marine Sciences Dunstaffnage Marine Laboratory Oban, Argyll, Scotland |
|